The slapper for the bottom fishing rod is not so difficult to make. But there is a reasonable question, and for what is it needed? After all, all the pleasure of fishing is precisely in the cutting and retracting of the fish. Here it is worth understanding the appointment of a slapper for the bottom fishing rod as auxiliary means when fishing using several rods.
Often, at bottom fishing, it is necessary to place rods on a decent distance from each other due to a certain terrain relief.
In such a situation, the automatic slapper will serve good service. You can deal with anything parallel to fishing. For example, if you need to reconfigure one of the gear in the event of a break.
The scheme of the auto shower is quite simple. The typical drawing can be found on the Internet. If you still decide to make an automatic pavement, pay attention to its execution.
Autocheteners can be divided into two classes:
- The first are installed directly on the rod or nearby. Their essence lies in the tension of the main fishing line with the help of a rubber cord. With its absence, you can use several banking (stationery) rubber bands. From a steel wire (an ordinary clip is suitable) a small lever is made. On the one hand, the lever is fastened, and with another gum under tension. The lever is located in the first rod ring. With a horizontal pulling line, the lever pops up from the ring. Next, the gum begins to shrink, caring the fishing line.
- With the second method, the leign mechanism is located on a leash. Autodistrics occurs directly in water. The essence of the method is again reduced to the spring mechanism. When bippying, fish frees one end of the lever, which is under tension. Stretching, the lever makes a sharp jerk of the main cord, thereby flowing down the fish.
The auto personnel will help to increase your catch. He will work faster than you find yourself near the rod.
Unusual options
Should be mentioned about interesting speciesPeople invented.
For example, a fleet of the float:
- in this case, the upper antenna is removed from the float;
- it is put on her homemade foam ring with a diameter of a little more antenna thickness;
- then the antenna is glued into its place. The ring should move freely on the antenna;
- from above the beads are fixed;
- when biting the ring does not allow the float to plunge into the water, flowing down the fish.
If the fish takes on the rise, this method will be useless.
Self-breeder for feeder, its use in fishing
Self-breaker for the feeder, as well as for other species fishing gear, refers to auxiliary devices whose benefits and efficiency is determined by time and circumstances of fishing. Such devices appeared not for a very long time.
At first it was a variety homemade deviceswhich invented fishermen came up with and manufactured for their fishing rods and crops. Now many devices contributing to automatic fish cutting are manufactured by industrial enterprises.
Purpose of automatic sheets
As you know, the most active and interesting part fishing Begins at the moment when fishing is happening. Some kinds of fish carefully, others are not very, they begin to try the bait taste. It is at this moment you need to produce effective covering. Such a cover is quite possible, if you catch on one fishing rod, and even better - if you constantly keep it in your hands.
If you catch on a few gears, which is often in feeder fishing, you just may not have enough time to react to bite, run up to the desired rod and spend the grip.
Self-breeders for fishing, just in such cases, will be very useful. Their main purpose - on time and with the desired effort to make fishEven without participating in this process of fisherman. These devices, during bite, provide required snap snaps in automatic mode. Often enough, experienced fishermen, based on the independently developed design, make a self-spinner for spinning with their own hands.
Such devices designed to learn fish without the participation of fisherman can be equipped with absolutely any fishing rods and bottom tackles. Most often with these mechanisms, depending on its device, equipped ordinary curtains, feeder gear and even flooring rods .
A spinning self-pedunning also exists, although in its need, many fishermen doubt, after all, catching spinning assumes that the form is all the time in the hands of the fisherman. The auto shower for spinning is rationally apply only when catching trolling or if the spinning is adapted under the feeder tackle.
Automatic fishing rod with a fleering agent is useful when long fishing When the fisherman cannot constantly be with her near, as well as in the case when fishing is carried out into several (sometimes at 4 - 5) rods.
Depending on its design and manufacturer, these devices are divided into the following types:
- Advanced tackle. This type includes floats and hooks, which, by entering into their design, certain changes, allow you to dry the fish without the participation of the fisherman.
- Various homemade structures. As a rule, the fleemer of fish made by its own hands and the scheme of its work is based on the same principle of operation as the usual mousetrap. The main driving force in them is either dense tires or a stretched spring of the required power.
- Industrial devices. This type includes technological mechanisms that are originally designed for this or that tackle.
Fishermen will often improve industrial samples of self-adjustments under their requirements, reinforcing or, on the contrary, somewhat weakening their sensitivity and validity.
Features of various types of slappers
The most important characteristic in the action of any automatic slapper, the power with which it affects the extraction is undoubtedly considered. In accordance with the necessary power of exposure, the power of tension used in the device of springs or rubber is calculated. It, as a rule, is the more significant than the harder the tackle for which the mechanism is intended. For example, a feeder for the feeder requires a greater force to act as a shortcutover for donkey with a short stick or without it.
It is also important to take into account the power that is necessary for removing the device from a safety stopper and initiation of actually covered. Stoppers and triggers, depending on the tackle, are also of different designs and power, but that it is necessary - all of them must be quite sensitive, it will ensure the response of the device to any, the most cautious bite.
It should be borne in mind that the cape-made slapper, manufactured by an industrial method, is calculated under a certain tackle, with specific requirements, only if it comes complete with this tackle. The remaining industrial mechanisms that have different principles of operation and power must be selected to their gear on their own and, if necessary, to refine them.
The slapper, made with his own hands, always takes into account the characteristics of that rod, the tackle for which was conceived and made. For example, the auto shower for spinning, the following factors must take into account the following factors:
- Weight and length of spinning.
- Approximate distance casting bait. This is important for the approximate calculation of the mass of the equipment in the water.
- When catching trolling - the strength of the flow and the speed of the boat movement.
- The dimensions of the alleged trophies, their appearance, as well as how typically occurs, the bite of this type of fish (carefully or rapidly) occurs.
If a fisherman, independently manufacturing an automatic pavement for its tackle, will be able to take into account all these factors and make a suitable device, the number of unnoticed or empty cute will significantly decrease.
In the manufacture of slappers intended for bottom gearFishermen often use a variety of runners in combination with rubber harness or converted mousetrap. Vertical racks are also common, which are fixed in the ground or in the boat boat, with powerful springs and corresponding staps.
Mansion, among all devices for automatic fish cutting, cost floats and hooks.
Float, contributing to self-vaccination, this is usually the usual float with an elongated central rod, supplemented by a disk from an insoluble material with a hole in the center for the passage of the upper part of the float rod and a special stopper (thickening) at the top of this rod. When bippying, the main part of the body float goes under water, but at the end there is a stopper's interaction with a disc, which sharply slows down his care under water and contributes to the saming of the fish.
Self-slip hooks They have a modified shape, somewhat similar to the spring, which contributes to its deep penetration into the sip of the fish and its crossroads. There are such hooks with only a few foreign enterprises and are rare on sale. Their main drawback is very difficult to free the caught fish from such a hook.
Example of a self-made self-seater for the feeder
We will analyze one of the options for the automatic pitch for the feeder, at which the rod is attached to the swinging element of the rack, by type of rocker, and the sinch is due to the springs compression. Such a mechanism can be made with your own hands. Its construction and the principle of action is easy to understand, having understood in the following scheme:
The numbers in the diagram are indicated:
- Rod (spinning).
- The front bracket of the rocker on which the fishing rod is attached.
- The body of the rocker.
- Fastening the axis of the rocker to the rack around which it rotates.
- Rear brace of rocker. Major attached top part Springs.
- Spring.
- The main stand of the slapper. It needs to be made of a stainless steel corner.
- Holes on the main rack. They are needed to enhance or weaken the springs stretching force.
- Cheerful rubber. It is necessary to mitigate the springs.
- Fastening rubber to the body of the bracket.
- The axis of the bracket.
- Trigger. It is performed from steel and must have a certain bending at the top for the possibility of slipping from the axis of the bracket at the sheet (you need to pick up the experimental way).
- Fastening the axis of the bracket to the corner housing.
- The main line with a snap.
- Coil.
Setting the mechanism is carried out after fixing the main rack in the ground. The sensitivity of the descent depends on the top bending of the trigger.
Useful video
In the video below, let's see an example of a self-breeder for the feeder in action:
Any self-adepening devices, industrial or performed independently, are designed to help fishing at fishing and not allow to leave extraction when biting. But still apply them only under certain circumstances, when without them it is impossible to do. After all, the joy of catching the trophy, which was lit alone, incomparably higher. Yes, and that fishing in which similar devices are used, it is impossible to call sports, rather - semi-automatic.
Simple mines for bottom tackle
Greetings all the fishermen self-dealers. Today we will make a simple self-breed for Donkee. The main advantage of this design is simplicity in manufacturing, it can be made of available materials with a minimum set of tools. The disadvantages include the dimensions and the need to align the platform on the shore of the reservoir for its installation. This design has already been tested and proved its performance. To whom it may seem that the spring turned out to be too powerful and the lever works very sharply, but it is not. IN real conditions Fishing, when the tackle is abandoned into the water, the covering looks quite different than in the workshop. It even seems that the power should be increased.
1. Visks.
2. Hammer.
3. Pliers.
4. Screwdriver.
5. Hoven for metal.
6. Wooden hacksaw (as needed).
7. Drill and drills (optional).
8. Roulette.
1. Board.
2. Steel spring wire with a diameter of 4-5 mm.
3. Cycling needles.
4. Galvanized metal with a thickness of 0.7 mm.
5. Nail.
6. Eraser.
7. Self-tapping screws.
As the basis of the deputy, we take a 40 to 12 cm board. Thick 1 cm. I will make a reservation at once, all sizes are very conditional and can change.
The most time-consuming part of the work is to bend a lescape of spring wire. We celebrate the edge of the wire 5 cm.
Cleash in vice and bend under 90 degrees.
Miffy the resulting bend with a hammer. The main thing is not to do everything so that the wire does not burst on the bend.
Now we celebrate 8 cm. From the bend also clamp in vice and bend in the opposite direction.
The most responsible part of the work, bend the wire 180 degrees. We note 5 cm. Press in the vice and for the beginning bending under 90 degrees.
Now, using a screwdriver and a hammer, neatly a cable wire 180 degrees.
If everything turned out, place the center of the leskoyller and a little bend.
We apply the resulting workpiece to the base and mark the beginning of the bend of the springs.
Cleash with vice and genets under 90 degrees. in the direction of the leskoisuator.
We note the size approximately equal to half of the width of the board and bend under 45 degrees. to the plane lever lever.
We mark 5 cm. And cut off the extra hacksaw.
The lever with a spring is ready, now we will make a wagon from bicycle needles.
We mark the edge of the knitting needles 5 times 2 cm.
Gennet pliers, forming the item, as shown in the photo.
On the other edge, the knitting needles bend the hook for fastening the lasty.
Now you need to secure the resulting details on the base. To do this, make four chomute from galvanized metal with a thickness of 0.7 mm.
We place four segments of about 4 to 1.5 cm. And cut off with a hacksaw.
Severed segments in the center using the remaining piece of wire as a pattern. Also, if there is something, you can round the edges.
Holes in the clamps under the self-sufficiency of course better drill, but if there is nothing, then you can break through the nail or dowel.
Fresh all the details to the base on the self-tapping screw. One clamp is better to put on the screws and make it removable, although it is not necessary.
Bend the lever of the slapper, mark the location of the waggered and fasten.
In order for the edge of the springs to do not clarify the board, we set another metal plate. To the top of the wagon, we install an eraser with a slot for fixing a fishing line or cord.
The self-breeder is practically ready, it remains to install another detail, without which it will not work. Here is such a hook.
It can be bent out of the nail and drive into the base. We found ready and screw it into the foundation in the center of the leskoyller.
Our slapper is ready to work.
Small council. To avoid accidental triggering in the alarming, it can be fixed for example a nail.
This sepper design is designed for bottom-type bottom tackle or gum.
The principle of operation is such. Throwing the tackle into the water, worker and fix the slapper, we draw a fishing line in the hook.
Fix in rosets.
Remove the retainer and wait for bite.
At the time of biting the closure comes out of the engagement and the spring is triggered. Fish on hook!
One clamp was made removable to make a lever of the slapper and it was convenient to transport it. We unscrew the clamp, we shift the lever to the edge of the base and put the clamp in place.
Nodes in more detail.
All or the tail either scales!
Video about making a mono self-vertex to see here.
Self-breaker for Donka
Fishing is an excellent view of the rest, but to be on the shore and keep the fishing rod in the hands, you need a lot of time. Fishermen often move to a snack, chat with friends or just relax. And at such moments fishing stops. To be able to sometimes move and disappear, automatic slats were invented. One of them is a self-breeder for the Donkey.
Why do you need an automatic flopper for fishing?
If there are several bottom gear when fishing is used, or the fisherman is simply distracted, you can miss the moment of good bite. Here will come in handy samopoders for the Donka. They will be able to keep the fish without the participation of the fisherman - to the neutral jerk. Fishing experts are able to make a slapper for the bottom fishing rod with their own hands.
Types of automatic sheets
Such devices can be installed on any rod. Most often installed on simple crops, feeders or rods with floats. The auto-ship for spinning becomes appropriate if the feeder tackle is installed on the rod.
Autocheteners can be installed:
- On the rod or next to him. With this variant, the fishing line will be stretched with a rubber cord. If it is not, a simple stationery is suitable. Also need steel wire (or simple clip) to make the lever. From one side of his side, a fishing line will be attached, and on the other - a stretched rubber cord. The lever will be in the first rings rod. If the pulling line is horizontal, the lever will pop out from the ring. Then the gum will shrink, and the fishing line is to reach it.
- In a leash. The covering occurs right in the water. The networking mechanism will be created based on rubber or springs. At the time of Poklevka, one of the stretched ends of the lever will be released. After the lever is straightened, it will make a sharp jerk, and the fish will turn out to be outside the water.
Both options allow you to increase fish catch several times. The main thing is that the mechanism for their work is installed correctly.
Fishermen constantly improve the designs, making them as comfortable as possible for their rod. Some walked them with their own hands from the girlfriend, others buy ready-made slappers to finalize the mechanism.
There are several types of automatic sheets:
- Improved tackle. In the design of the hook and the float, some changes are made, thanks to which the covering will be automatic.
- Homemade design. The auto shower, made by its own hands, on the principle of operation, is similar to a mousetrap: the basis of its movement is either rubber or spring.
- Industrial deposits. These designs are made for certain gear.
Fishermen can buy an industrial kit and change it at their own way.
Self-breaker for donkey do it yourself
To assemble the mechanism, you will need:
- Fishing rod;
- Fastening that will keep the fishing rod (consists of two parts - the front bracket, and the main part);
- Fixing part (connects the bracket and the main part, is responsible for lifting fishing rods);
- Rear bracket;
- Spring of a certain power;
- Depreciation rubber;
- Holes on the main part of the attachment;
- Axis brackets;
- Rubber, which is attached to the body of the bracket;
- Steel trigger (with a bend at the top so that the bracket can slip when with a sheet);
- Fastening the bracket to the main part;
- Fishing line;
- Coil;
- Tackle.
The whole design is fixed in the ground. Sensitivity will depend on the trigger.
Materials
List of tools and materials for making a self-breed on the Donka:
- Aluminum plate;
- Wire with a diameter of 2 mm;
- Kanenaya plate;
- Wooden plank;
- Pliers;
- Screwdriver;
- Nippers;
- Rubber or spring;
- Plastic (computer discs are suitable);
- Aluminum rod;
- Pin;
- Bolts and nuts.
Naturally, it is necessary to prepare the rest of the necessary attributes of fishing:
Manufacture
- Aluminum plate bend in the form of the letter P with the sides of 2 cm.
- Drill 2 holes with a diameter of up to 2 mm with each bent side.
- Screw about three turns of the wire on a rotary plate. It will perform the role of a spring.
- Bend the end of the wire so that it is in the form of a large hook.
- Install the wire into the aluminum plate, put on the spring. On the opposite end to put on the Cambrick. It will be a retainer. Hoall the end of the wire.
- Now it is necessary to wrap the long end of the springs of the loop around the wire.
- Fasten the mechanism at the very end of the table, along with a wired ring.
- Substitute a folding structure so that she touches to the wagon.
- Using several screws, attach a plate to a wooden board. Design ready.
- When installing an automatic panel, you need to be attentive and inseparable. The overthrown of the sheets, tension of rubber or spring is always large. If the slider jumps out beyond the base, there is a risk of injury.
- If the water is calm or minimal, it is recommended to set up a trigger for a minimum. This will increase sensitivity.
- To attract more fish to bait, you can install an elastic band with a feeder.
Other solution solutions
There are also options invented by simple fishermen. One of them is an automatic float cover. It is assembled in this way:
- From the float pulls out the upper antenna.
- You need to wear a ring from the foam rubber. Ring size - a little more antenna.
- Now you need to return the antenna in place. At the top to attach a bead.
- In the cooking process, the ring will not allow the float to go to the bottom, and the fish will be counted.
The automatic pavement is indispensable if the fishing has been dragged and you want to relax, but at the same time do not lose catch.
Slicers for bottom fishing rod and fider
Many fishermen are fond of several types of fishing. To combine running fishing with spinning on a predator from the shore and a calm seitant hunting for white fish With a bottom or float tackle, you need to be a rare lucky or professional. When you are aside, trying to lure predatory fish, To keep track of a bone-baked bottom tackle, to react in time, then run to the place where the fishing rods are exhibited, it is practically unable. The way out of such a situation is still available - this is an automatic cover when biting without the participation of fisherman. The slapper for the bottom fishing rod can be made and installed directly on the shore of the reservoir.
Types of devices for auto party
The practice of using devices with an autochetemer installed on the rod is used not one decade. The design of the self-breeder is offered:
industrial manufacture. Such options have a complex structure, often large dimensions, a high price;
self-made production. Presented with a large number of execution options for which inexpensive infringement materials are used. Free access has drawings and the order of assembling such devices.
Industrial production deposits replace the stand are used to install rods in them. They require care, are subject to corrosion, have complex technical solutions for the compound. The moving parts of the mechanism of auto party are clogged with mud, sand, the springs are deformed, because of what kits of blesses and idle covers occur.
Self-showers of self-made production, in contrast to purchased, have a budget value. Ospects when used are practically excluded. Easy design allows you to use such structures in any natural conditions, does not require additional maintenance and care.
Simple and budgetary design
The homemade chipper for the feeder is easy to make two stationery and paper clips. Such a device after throwing a donkey fixes the main fishing line, and during the bite at the right moment the fish floods.
The procedure for applying and manufacturing a self-made slapper for the feeder:
the gums are connected in one product to each other and are fixed by one end behind the feet of the coil;
the clip is straightened into a flat wire, with the help of the passage, bends in the form of hooks in its edges are formed;
after throwing bait into the water upgraded wire hook with a single crochet, fixed on the first rod ring;
using the main fishing line, the self-spinner is divided, a free wire hook is fixed.
Based on the float
Folk savings and ingenuity showed themselves in fishing a fishing tackle. It happens when the Klev is activated, and to catch two or three fishing rods is physically not obtained. Book is happening, and the ringing of the fisherman does not have time. For such situations, a samopodemaker based on the float was invented. Production principle simple:
- a flat foam cylinder is cut, the size of which is determined by the experimental path of the float diameter;
- the selected segment of the foam rubber dress up onto a vertex free stroke It is fixed by a bead with a cambrick.
When biting a modified design goes under water. In this case, the cylinder creates a substantial immersion resistance, and self-saming occurs.
Analogue of industrial manufacture
As a rule, purchased automatic holders have a high price and are not always made of durable material. Therefore, having a necessary set of tools and a sufficiently budget amount of funds, you can make such a device yourself.
List of tools required for manufacture:
- passatia;
- grinding with cutting circles;
- welding machine, electrodes;
- drill;
- a hammer;
- tees;
- marker or chalk;
- tassel for paintwork.
- armature, a diameter of 8-10 mm for the manufacture of legs;
- sheet iron 2 mm thick and 5 mm;
- spring Door 50 - 80 cm long.
The procedure for making a self-breeder with a rod holder:
- according to the drawing, the reinforcement for the manufacture of legs is measured, cuts off with a grinder;
- prepared bars are formed using hammer and tees;
- from the sheet metal (thickness 2 mm) are cut staples, holding a rod, spring and leneting mechanism;
- in the retention bracket, the holes are drilled;
- the leaflength tongue is made of iron with a thickness of 5 mm;
- cut and prepared parts are welded in the right order;
- the design is painted.
Output
The use of automatic sheets is advisable and confirmed by the number of fish in the catch. With their help manage to combine fishing and rest, as well as different types fishing. The saying "You will hit two hares, you can't catch one" with such assistants is refuted.
Fishing - A great view of the rest, but to be on the shore and hold the fishing rod in your hands, you need a lot of time. Fishermen often move to a snack, chat with friends or just relax. And at such moments fishing stops. To be able to sometimes move and disappear, automatic slats were invented. One of them -self-breaker for Donka.
If on fishing is used some Or the fisherman just distracted, you can miss the moment of good bite.Here and comeself-breeders for Donka. They will be able to keep the fish without the participation of the fisherman - to the neutral jerk. Fishing professionals are able to makeslicer for bottom fishing rod.
Types of automatic sheets
Such devices can be installed on any rod. Most often installed on simple crops, feeders or rods with floats.The auto-ship for spinning becomes appropriate if the feeder tackle is installed on the rod.
Autocheteners can be installed:
- On the rod or next to him. With this variant, the fishing line will be stretched with a rubber cord. If it is not, a simple stationery is suitable. Also need steel wire (or simple clip) to make the lever. From one side of his side, a fishing line will be attached, and on the other - a stretched rubber cord. The lever will be in the first rings rod. If the pulling line is horizontal, the lever will pop out from the ring. Then the gum will shrink, and the fishing line is to reach it.
- In a leash. The covering occurs right in the water. The networking mechanism will be created based on rubber or springs. At the time of Poklevka, one of the stretched ends of the lever will be released. After the lever is straightened, it will make a sharp jerk, and the fish will turn out to be outside the water.
Both options allow you to increase fish catch several times. The main thing is that the mechanism for their work is installed correctly.
Fishermen constantly improve the designs, making them as comfortable as possible for their rod. Some walked them with their own hands from the girlfriend, others buy ready-made slappers to finalize the mechanism.
There are several types of automatic sheets:
- Improved tackle. In the design of the hook and the float, some changes are made, thanks to which the covering will be automatic.
- Homemade design. The auto shower, made by his own hands, on the principle of operation, is similar to a mousetrap: the basis of its movement lies eitherrubber or spring.
- Industrial deposits. These designs are made for certain gear.
Fishermen can buy an industrial kit and change it at their own way.
Self-breaker for donkey do it yourself
To assemble the mechanism, you will need:
- Fishing rod;
- Fastening that will keep the fishing rod (consists of two parts - the front bracket, and the main part);
- Fixing part (connects the bracket and the main part, is responsible for lifting fishing rods);
- Rear bracket;
- Spring of a certain power;
- Depreciation rubber;
- Holes on the main part of the attachment;
- Axis brackets;
- Rubber, which is attached to the body of the bracket;
- Steel trigger (with a bend at the top so that the bracket can slip when with a sheet);
- Fastening the bracket to the main part;
- Fishing line;
- Coil;
- Tackle.
The whole design is fixed in the ground. Sensitivity will depend on the trigger.
Materials
List of tools and materials for manufactureself-breaker on Donku.:
- Aluminum plate;
- Wire with a diameter of 2 mm;
- Kanenaya plate;
- Wooden plank;
- Pliers;
- Screwdriver;
- Nippers;
- Rubber or spring;
- Plastic (computer discs are suitable);
- Aluminum rod;
- Pin;
- Bolts and nuts.
Naturally, it is necessary to prepare the rest of the necessary attributes of fishing:
- Rod;
- Hooks;
- Bait;
- Fishing line;
- Coil.
Manufacture
- Aluminum plate bend in the form of the letter P with the sides of 2 cm.
- Drill 2 holes with a diameter of up to 2 mm with each bent side.
- Screw about three turns of the wire on a rotary plate. It will perform the role of a spring.
- Bend the end of the wire so that it is in the form of a large hook.
- Install the wire into the aluminum plate, put on the spring. On the opposite end to put on the Cambrick. It will be a retainer. Hoall the end of the wire.
- Now it is necessary to wrap the long end of the springs of the loop around the wire.
- Fasten the mechanism at the very end of the table, along with a wired ring.
- Substitute a folding structure so that she touches to the wagon.
- Using several screws, attach a plate to a wooden board.Design ready.
- When installing an automatic panel, you need to be attentive and inseparable. The overthrown of the sheets, tension of rubber or spring is always large. If the slider jumps out beyond the base, there is a risk of injury.
- If the water is calm or minimal, it is recommended to set up a trigger for a minimum. This will increase sensitivity.
- To attract more fish to bait, you can install an elastic band with a feeder.
Other solution solutions
There are also options invented by simple fishermen. One of them is an automatic float cover. It is assembled in this way:
- From the float pulls out the upper antenna.
- You need to wear a ring from the foam rubber. Ring size - a little more antenna.
- Now you need to return the antenna in place.At the top to attach a bead.
- In the cooking process, the ring will not allow the float to go to the bottom, and the fish will be counted.
The automatic pavement is indispensable if the fishing has been dragged and you want to relax, but at the same time do not lose catch.
As you know, the most active and interesting part of the fishing begins at the moment when fishing is happening. Some kinds of fish carefully, others are not very, they begin to try the bait taste. It is at this moment that you need to make an effective backup. Such a cover is quite possible, if you catch on one fishing rod, and even better - if you constantly keep it in your hands.
Important! Always, on every fishing, you need to take into account the physiological features of the kind of fish that you catch. From this depends the force and the speed with which it needs to be lined.
If you catch on a few gears, which is often in feeder fishing, you just may not have enough time to react to bite, run up to the desired rod and spend the grip.
Self-breeders for fishing, just in such cases, will be very useful. Their main purpose - on time and with the desired effort to make the fish, even without participation in this fisherman process.
These devices, during bite, provide the necessary snap snap in automatic mode. Frequently often, experienced fishermen, based on independently developed design, make a self-spinner for spinning with their own hands.
Such devices designed to learn fish without the participation of fisherman can be equipped with absolutely any fishing rods and bottom tackles. Most often by these mechanisms, depending on its device, ordinary capes, feeder gear and even float fishing rods are equipped.
A spinning self-pedunning also exists, although in its need, many fishermen doubt, after all, catching spinning assumes that the form is all the time in the hands of the fisherman. The auto shower for spinning is rationally apply only when catching trolling or if the spinning is adapted under the feeder tackle.
Automatic fishing rod with a fleet will come in handy with prolonged fishing, when the fisherman cannot constantly be with it near, and also in the case when fishing is carried out into several (sometimes at 4 - 5) rods.
Depending on its design and manufacturer, these devices are divided into the following types:
- Advanced tackle. This type includes floats and hooks, which, by entering into their design, certain changes, allow you to dry the fish without the participation of the fisherman.
- Various homemade structures. As a rule, the fleemer of fish made by its own hands and the scheme of its work is based on the same principle of operation as the usual mousetrap. The main driving force in them is either dense tires or a stretched spring of the required power.
- Industrial devices. This type includes technological mechanisms that are originally designed for this or that tackle.
Fishermen will often improve industrial samples of self-adjustments under their requirements, reinforcing or, on the contrary, somewhat weakening their sensitivity and validity.
Features of various types of slappers
The most important characteristic in the action of any automatic slapper, the power with which it affects the extraction is undoubtedly considered. In accordance with the necessary power of exposure, the power of tension used in the device of springs or rubber is calculated.
It, as a rule, is the more significant than the harder the tackle for which the mechanism is intended. For example, a feeder for the feeder requires a greater force to act as a shortcutover for donkey with a short stick or without it.
Attention! As a rule, over time, the springs are stretched and somewhat losing their power. This must be taken into account when setting up a self-adjustable mechanism.
It is also important to take into account the power that is necessary for removing the device from a safety stopper and initiating actually covered. Stoppers and triggers, depending on the tackle, are also of different designs and power, but that it is necessary - all of them must be quite sensitive, it will ensure the response of the device to any, the most cautious bite.
It should be borne in mind that the cape-made slapper, manufactured by an industrial method, is calculated under a certain tackle, with specific requirements, only if it comes complete with this tackle. The remaining industrial mechanisms that have different principles of operation and power must be selected to their gear on their own and, if necessary, to refine them.
The slapper, made with his own hands, always takes into account the characteristics of that rod, the tackle for which was conceived and made. For example, the auto shower for spinning, the following factors must take into account the following factors:
- Weight and length of spinning.
- Approximate distance casting bait. This is important for the approximate calculation of the mass of the equipment in the water.
- When catching trolling - the strength of the flow and the speed of the boat movement.
- The dimensions of the alleged trophies, their appearance, as well as how typically occurs, the bite of this type of fish (carefully or rapidly) occurs.
If the fisherman, independently manufacturing an automatic pavement for its tackle, will be able to take into account all these factors and make a suitable device, the number of unnoticed or empty biplons will significantly decrease.
In the manufacture of flooring, intended for bottom gear, fishermen often use a variety of sluts in combination with rubber harness or converted mousetrap. Vertical racks are also common, which are fixed in the ground or in the boat boat, with powerful springs and corresponding staps.
Mansion, among all devices for automatic fish cutting, stand floats and hooks.
Float, contributing to self-vaccination, this is usually the usual float with an elongated central rod, supplemented by a disk from an insoluble material with a hole in the center for the passage of the upper part of the float rod and a special stopper (thickening) at the top of this rod.
When bippying, the main part of the body float goes under water, but at the end there is a stopper's interaction with a disc, which sharply slows down his care under water and contributes to the saming of the fish.
Example of a self-made self-seater for the feeder
The numbers in the diagram are indicated:
- Rod (spinning).
- The front bracket of the rocker on which the fishing rod is attached.
- The body of the rocker.
- Fastening the axis of the rocker to the rack around which it rotates.
- Rear brace of rocker. It is fastened to the top of the spring.
- Spring.
- The main stand of the slapper. It needs to be made of a stainless steel corner.
- Holes on the main rack. They are needed to enhance or weaken the springs stretching force.
- Cheerful rubber. It is necessary to mitigate the springs.
- Fastening rubber to the body of the bracket.
- The axis of the bracket.
- Trigger. It is performed from steel and must have a certain bending at the top for the possibility of slipping from the axis of the bracket at the sheet (you need to pick up the experimental way).
- Fastening the axis of the bracket to the corner housing.
- The main line with a snap.
- Coil.
Setting the mechanism is carried out after fixing the main rack in the ground. The sensitivity of the descent depends on the top bending of the trigger.
Source: Ribaulov.ru.
All fishermen are familiar with such a situation where the long-awaited bone occurs at the moment when the fisherman returned from the gear, and naturally pecks the most big fish. We will make an easy self-breed to avoid such unpleasant situations on fishing.
Having needed tools and fixtures.
1. Angle grinding machine.
2. Drill with a set of drills.
3. Kiyanka.
4. Set of nadfile.
5. Visits.
6 sandpaper.
7. Knife.
Having needed materials.
1. Aluminum profile, with sizes of shelves three per centimeter.
2. Sheet aluminum thickness of one and a half millimeter.
3. Spring.
4. Small screws with nuts.
5. Soft rubber thick two centimeters.
6. Clips for mounting metalplastic.
As the basis of the self-breeder, we take the aluminum profile three per centimeter. Cut off the segment of twenty centimeters from it and cut one and a half centimeter shelf.
We remove the sovereignty with a dumplings, spin the edge and cleaner with sandpaper.
For the next part, Ideally, it would be nice to have a profile that would be inside the first but since such a profile was not found, it was bent from the leaf aluminum thickness of one and a half millimeter.
We clamp the aluminum sheet in the vice between the two metal corners and easily tapping with the Cyanka bend the first shelf.
In the second shelf, bend the detail of the vice, inserting the insertion of the required thickness into the insert.
Finally align the resulting profile overlooking it on a sheet of metal with a thickness of five millimeters.
One side of the workpiece is slightly cutting off on the cone and we make a small cut from above. Detail I am cleaned by I.
okrinate.
From the same aluminum sheet, cut a segment for fifteen centimeters for two centimeters. We make a small propyl, I spin the edge and also remove the sowing and cleaner with emery paper. It will be a watchhead.
Drills holes and collect the resulting details together, on small screws. For fixing the clutch, install an additional screw.
Inside the slapper, we set the spring.
On the top of the wagon, we fix the soft rubber, in which the knife make an incision for fixing the fishing line or cord.
For the attachment of the received self-sampler to the rods, mounted clips, which are used for the installation of metal-plastic or polypropylene water pipes. These clips are of different sizes so finding a specific rod will not be difficult.
The self-spinner is ready, we install on the rod, we will, fix the fishing line or cord in a cutlery on the rubber vessels, and wait for bite. At the time of pulling the fishing fishing, the wagon is coming out of the engagement and automatic coverage occurs.
All or the tail either scales!
The video for the manufacture of a self-breed can be viewed here.
Source: USAMODELKINA.ru.
Option 1
The self-spinner is intended for use with a fishing rod or spinning and spring properties. During a bunch, a bent rod is released by the panel mechanism, as a result, the fish is carried out without any actions of the fisherman.
In the image, we can consider the general scheme of the principle of operation of such a system.
To connect the details of the design of the self-vectors, wire sleeves are used, which are disappeared, or bolts - you can choose one of these solutions.
Different options are suitable as a material - steel with galvanized or without, better brass. In general, what will be at hand.
All elements of the homemade need to be combined and at the same time to monitor - moving parts should move easily, they will not stick anywhere. You can at a minimum of dripping machine oil.
Now we have one part of the self-made auto party. Holder for installing fishing rod or spinning can be made with your own hands or buy a ready-made glass. Or take some other subject of a suitable form to secure the rod on it. For example, you can use the scheme below.
AvtoFeemer is ready. You can put a mechanism of homemade covers to the operating position and wait for the fish on the hook.
Option 2.
I met somehow a self-breeder for American-made fishing. It is made in a satisfied simple design, as with other options, so there will be no difficulties in its manufacture.
The principle of operation of such a device and how to use it - you can learn from the above images.
No need to be afraid to make experiments. Fishing is the hobby to which you can approach creatively.
Option 3.
Original float - and auto party
Depending on what kind of fish you are going to catch, you should and choose some kind of tackle for the fishing rod - the line, hooks, float. Fish of some species is very voracious. The peculiarity of catching such a fish is that it is possible and the eye does not blink - and the fish has already come across the hook, deeply swallowed it with a bait. In this case, the hook pull is quite difficult. To take it out and freeing the fish, you have to take a tweeze or some other item.
In order to avoid such uncomfortable situations, you can make a peculiar samopod in the form of an improved conventional float.
To do this, take the usual store float, it should have a thin and long top rod, at the end of which the thickening is located in the form of a head. To improve this float, you need to take a small piece of foam or cortex.
First we take the plug (or foam) and cut off the fragment in the form of a mug, its thickness should be 5-10 mm. After that, you need to take the drill and in the center of the mug make a hole. Its diameter should be such that the circle is mounted on this rod freely moved up and down, while the head of the rod will serve as a limiter to its movement. When the hole is ready, you need to take a blade or a sharp knife, and make a slot from the hole to the edge of the circle.
It is necessary so that the circle is injected on the float, or remove it if you need. The circle is better not to cover the paint, since, due to extraneous smells, fish in water can simply have a bait.
The work of such an improvement is built according to the following principle. In some fish - for example, perch or rhotan there is such a feature - they grab the bait very sharply. In the case of a sharp biplate, the float goes under water, and the circle will stop the float head on the water - and thus flows down the fish. In such an easy way, the defined float of the catch is significantly increasing. As practice shows, such a self-servant works with his own hands, even if you do not have anything near the fishing rod.
Source: www.umeltsi.ru.
What do you need a self-breeder and its advantages
The main purpose of the self-breed is that when the fishing line is taking a fishing line because of the fishing, make a jerky jerk, thanks to which the hook will perform its function and will only leave the fish in the submers.
In addition, he is not enough, because it only informs fisherman about fish activity, but does not make an independent back.
A properly configured clutch of the coil does not allow drowned fish to break the equipment or drag it into the squigs and the use of self-showers favorably affects the size of the catch and the results of fishing. This is especially brightly manifested when fishing at night, when the fisherman rests and does not follow the status of the gear.
Although in the daytime it is not always possible to be near the rods and because of this there are idle work devices.
Varieties of autocheteners
Each missed bite is a potential loss of fish and is not surprising that fishermen come up with devices that increase the efficiency of fishing.
To such devices and include self-coaching agents installed on:
- form of the rod, or located near the racks on which a donkey is installed;
- before the leash, when the process of cutting fish occurs under water.
Which version of the self-breeder is more convenient - it is to solve the fisherman himself, the main thing to make the choice is consciously and evaluate all the advantages and disadvantages of the design, which, unfortunately, is.
The design of the self-vectors installed next to the Donka or directly on the form involves stretching the fishing line due to the elasticity of the rubber cord used, or the gum used in the aircode. For the fixation of gum and a combination with a rod, a wire design is used, the manufacture of which will be discussed below.
Peepers on the leashes are used mainly by floats that perform neat and accurate casts in the near distance. Donochers have to throw snap-to-digging and the design of the self-breeder does not withstand the load, it will straighten up in flight.
In any case, the fans of the bottom fishing is useful to know how the design of the leiner samopodemer is arranged, because it can be used when fishing at a distance of 15-25 meters. In feeder fishing, such distances are fully familiar, so the use of a self-person will be fully justified.
Auto shifts differ in the type of tension used, and it can be:
- rubber;
- springs;
- rigid wire.
The simpler the design of the device, the more durable, but the service life depends on the materials used. The elements of the design that are responsible for the tension and the triggering of the pavement mechanism must be resistant to the effects of moisture, the sun and wind.
Rubber in this regard is more profitable for metal springs, but when contacting with sand, burrs appear on it, and then cliffs and especially disappointment, if this happens during the fishing session. Therefore, on fishing you need to have spare gum with me, to continue fishing even when a slapper breakage.
Sticted rigid wire is the cheapest and affordable material for the manufacture of autocheteners, but it is "afraid of water", which means short-lived. In any case, homemade devices for donkey cover are not designed for long-term operation, and make them with their own hands is completely simple.
In winter when fishing software open water It is impossible, there is time in order to make self-showers for the future season in the right quantities.
Advantages of homemade
The slapper is necessary for all those who catch more than 2 rods and on fishing prefers not to sit before rhodes or racks waiting for a bite. For example, the same carpakens have to wait for bite for several hours, and each caught fish is very important.
The manufacture of homemade self-sustainers for donok does not require significant financial spending, after all, affordable and inexpensive materials are used. This is another important argument in favor of making a device to cover your hands and not have problems on fishing.
Even with strong wind or rain, a qualitatively made autochetemer remains at workable condition until the moment does not nourish the fish. In anticipation of fisher bolt can be engaged in other affairs, because the state of his donok is closely monopulating.
Production of a self-breed
As you know, when biting a fish takes a hook with a nozzle, and when creating resistance, the sting penetrates into the lip and flows the trophy. I.e the main task The slapper is to create an effort towards the opposite of the Powing of the Fish.
As an example, we give the float tackle, for which the slapper is very simple. When biting, the float is immersed in water under the weight of the trophy and it is enough to increase its buoyancy for serif, or resistance.
For this purpose, a foam cylinder is glued in the body of an antenna with body antenna and the antenna is inserted into it. When biting the float is not sinking, as usual, but it remains on the surface and due to this, the fish can be cut.
From the clips
The most common type of autochetemer for donkey is made from:
- big stationery clips;
- elastic gums, or a piece of aircraft rubber connected by a ring.
This device is fixed on the rod, and after the fisherman's cutting, nothing interferes calmly to start the fish in the subcase. Naturally, instead of a clip, a segment of a rigid wire 15-20 cm long is suitable. The clip has an anti-corrosion coating, and does not rust after wetting on fishing. Therefore, in the absence of clips, choosing a wire, you need to pay attention to that it also has a coating.
Advantages of the autochetemer of a paper clip:
- small sizes (5-7 fixtures will easily fit in a fishing box of medium sizes);
- quick installation on the rod, as well as dismantling after fishing;
- high sensitivity;
- sharp and clear cover.
When digging fish, such a slapper does not create an interference of the fisherman and is quickly driven into the working position. The main element of the panel is a wire, and the framework of it is made of it.
The process of making a samopodenty paper clip:
- the clip is aligned along the entire length;
- one of the ends of the wire 3 cm long bends at an angle of 120 degrees, it will cling to the rod ring;
- 1 cm below the curved segment with the help of the round-rolls is made by the ring in which the rubber will be done;
- at the other end of the wire, the round-rolls are made by a rectangle with a side of 2 cm, a fishing line will be made to it;
- 0.5 cm below the rectangle clip is strung at an angle of 90 degrees;
- in the ring of the self-spinner, the gum is inserted by the loop method in the loop.
The self-breeder is ready and remains only to install it on the rod.
For this:
- the gum is attached to the coil by any convenient way;
- the curved end of the wire is attached to the first ring of the Donkey.
The stretched gum holds the self-breed in the angle at an angle of 90 degrees relative to the born of the rod. After throwing the tackle, the fishing line will start in a wire rectangle and the slapper is ready for operation.
When biting fish, the fishing line pulls the wire trigger, and the curved end swings from the rod rings. Because of the elasticity of rubber, pulling the wire frame, there is a sharp pulling of the fishing line to the side, the opposite direction of the movement of the fish and it flows.
The maximum sensitivity of the device is adjusted on fishing and for this, the end of the wire, fixed on the rod ring, is strifted at the desired angle (it can be slightly smaller, or more than 120 degrees). It will be clear enough to simulate fish bumps and it will be clearly seen how quickly the curved end of the slapper jumps from the rod rings, and what an effort to do this for this.
For such a self-breeder, a rather rigid wire is needed so that it keeps the initial shape even after a set of backs. Find such a wire (if there is no big stationery clips) is completely simple in any farm. The same applies to elastic bands that are purchased in stationery stores.
Some fishermen cling the self-vehicles from the wire are not on the bottom, but on the upper ring of the rod, but when digging the fish, they create interference winding fishing line on the coil.
Simple auto shower
To cover the fish, it is necessary for the rod mounted on the rack at the moment of bite sharply changed its position. Even drops from the rack of the form are enough to suspend the fishing line and, accordingly, serfs of fish. According to this principle, the easiest cooler of the wire mounted on the rack is working.
The design of the device consists of a wire frame or a frame that is fastened to the rack and after throwing tackle to it, a rod is installed. The frame is made in the form of a rectangle without one hand, and the tip of the form is put on the edge next to this "unclosed" side.
With a bunch of fish, the tip of the rod squeaks from the frame, it pulls the fishing line and the trophy is fighting. It will take no more than five minutes to make such an auto-shift, but it copes perfectly with its functions.
For the manufacture of a given self-coaching agent, a rigid wire is needed, capable of keeping the weight of the tip of the rod even in a strong wind. To fix the fishing line in the desired position on the tip of the rack, the knobs are worn from porous rubber, on the one hand, reliably holding the fishing line, on the other hand, in the case of a bite, quickly exempted it.
Stationary self-person
Self-changing docks were widespread from fishing lovers and many of them show fantasy and modify well-known designs, improving their functionality. Along with the devices that are fastened with a rod form, in fishing are also stationary samopoders who have certain advantages.
So, the advantages of stationary devices is:
- sensitivity;
- functionality;
- thin tuning under certain conditions of the reservoir;
- durability.
Agree that even with the most neat operation, the auto shower of the paper clip is short-lived. Even despite the simplicity of the design, before each fishing, there are new slats mounted on a rod, not too convenient, and even the richest and rigid wire still loses its elasticity.
Stationary devices are more durable and their actively use donochetes on rivers, with a lot of rods. The main and, perhaps, the only disadvantage of stationary autocheteners are large sizes, but compared to their advantages is not a critical circumstance.
Consider a slapper working on the mousetrap principle, when during the pawing, the blocking device is triggered, lifting the rod, due to which the hub occurs.
For the manufacture of such a slapper will need:
- segment of a 50 cm board with a width of 10 cm;
- two segments of steel wire 50 and 30 cm long;
- clamps for fastening the wire to the board;
- screws for screwing the clamps to the board;
- eraser;
- bicycle needles for making a bracket for a fishing line;
- plastic cambrick to protect the fishing line, which is put on the bracket.
Of course, the instruments will also be needed:
- round-rolls;
- screwdriver for screws;
- pliers;
- a hammer.
In order for the product to be durable, choose a particularly durable steel wire, retaining rigidity for a long time.
The process of manufacturing a slapper:
- on a segment of a wire with a length of 50 cm of edge, the pliers are strung up so that 5 cm from each edge "watched" in different directions at an angle of 90 degrees and one of the ends bends as λ;
- on one of the second segments of the wire (30 cm long), an eraser is satisfied, and the second is strung in the form of a bracket or in the form of Ω;
- the segments of the wire are screwed by clamps to the chalkboard opposite each other so that the "tongue" of one segment came under the "bracket" of the second;
- a bracket is made from the bike knitting needles, the Cambrick is put on it, and they are screwed to the board right in the middle.
A design is obtained, in which the segment of the wire with a row eraser serves to install the fishing line and fixing the "tongue" of the second segment. The fishing line starts in the bracket and due to the stiffness of the wire, the tension is tension at the head of "tongue". Pokleka fish leads in motion the fishing line, and hence the wire with an eraser. The bracket frees the "tongue" and the wire design dramatically pulls the fishing line, connecting the fish.
This type of self-made, stationary slapper allows you to adjust the sensitivity of the structure. For this, the "tongue" starts further or closer under the bracket and already at minimum pressure, the device works on the suspension of the fishing line. Thanks to the attachment on the clamps, after fishing, the autocheteer is developing and during transportation, the design retains its shape.
Someone will say that a lot of time is spent on the manufacture of a stationary slapper, but the advantages that it provides fishing in order to spend it. In addition, some special skills are not needed for this and almost any fishing lover will cope with the help of girlfriend tools.
The use of self-adjustments increases the effectiveness of fishing, and even large trophies are easily born using such devices. With a low cost and accessibility of components, the self-breeder helps a lot on fishing, especially if fishing is conducted on bottom tackles.
Tarnings for fishing regularly replenish the range of new fixtures that simplify the fishing process. The samopoder for the feeder applies precisely to such accessories by which the number of catch increases at times. With feeder catch, such a tackle is especially important, since it allows you to quickly react to bite without the participation of the fisherman.
Autodistrank is often used when fishing on more than one fishing rod, which is not uncommon for feeder fishing. Also, it is also advisable to get a self-breeder if bite takes place rarely or fishing falls at night. In fishing, you need to take into account the breed and the physiological features of the fish you want to extend. The strength and speed required for the sheets depends on this. The purpose of self-vehicles is as follows:
- timely and with the desired force to perform a network without the participation of fisherman;
- provide snap snack in automatic mode;
- run a sheet if the fisherman fell asleep with nightfings.
Devices for auto party quickly react even on a weak kvel during feeder fishing and provide the necessary leak tension. It increases the chances of returning home rich catches, it allows you to engage in parallel with fishing some more thing, and also makes it possible to catch fish without the need to be present personally.
Technically, the self-spinner looks like this:
- the reference rack is necessary to install the device on the shore;
- the rocker - to fasten the rod handle;
- spring - Creates a feeder jerk up (pinch) when swallowing the hook fish;
- the trigger (trigger) - helps to work the rocker when tensioning fishing fish.
The design features of the self-spinner, with the right setting, eliminates the "empty" sheets. For each type of catching they are individual. Some have fasteners for a rod. For feeder gear it required condition. Also important is the elasticity of the spring, the characteristics of the structure and the strength of the curric, depending on the type of gear and the weight of the alleged production.
Types of self-adhesors for different types of gear
Devices for auto party are equipped with any tackle used, including donks. Most often, these devices are mounted on float fishing rods, ordinary inquiries and feeders.
Constructively devices are divided into:
- upgrade - floats and hooks, which, at the expense of small modifications of their design, allow you to check without angler;
- homemade - fixture made by personnel and working on the principle of mousetrap;
- factory - technological mechanisms intended for a specific type of tackle.
Depending on the chosen gear, the slappers are:
- for Donki - help to produce autodists when fishing on a standard bottom rod;
- for feeder - a wide variety of devices intended for installation on tackle. Special hooks can be used, constructive features which are allowed when swallowing and tightening fish easily and enter the shatter in fish to fall and set out there when digging;
- for fishing rods - apply devices similar to feeder or special floats, having a movable puck on their antenna.
With an active Kleva, auto party is not needed, because Most of the fisherman's time will go to recharge the device, thereby distracting it from bite.
Also sewers are separated by installation methods. There are three options for fixing the device.
- On the shore near the rod. Mostly this device homemade type with a special wooden stand. Located in the course of the fishing line.
- On the feeder form. The tackle in place behind the coil is formed under 90 degrees immediately after throwing the bait. The feeder handle is fixed in the holder, the long part looks at the water. At the moment of bite, the fishing line leads the trigger, the spring is triggered, and the self-spinner jerks the fishing rod up, performing the sheet. This option is acceptable using a very light fishing rod, the length of which is not more than 2 meters. Of the cons of such a mechanism, it is possible to note the possibility to be covered by corrosion, due to the fact that it is made of steel. The second drawback is a stretching over time of the spring that requires its replacement.
- On the stand rods. Handle tackle is located and fixed on a special bracket, which at the moment of bite races the rod up. It happens at the time of the tension of the fishing line, hooked behind the hook of the litter.
The choice of the installation of a self-breaker depends on the personal preferences of the fisherman and the type of tackle used for fishing.
Features and rules for using a self-breaker
Considering that only industrial mechanisms have settling under a specific type of gear, select and configure another type of self-specifier, you need to practice and error. Before applying the device, some nuances must be taken into account:
- weight and length of the rod;
- an approximate distance to which the bait is planned;
- stream stream and boat speed;
- features of fish, its size, weight, type of bite.
Compliance with these rules will significantly reduce the amount of empty cowlers and increase the catch.
Autodists easily cope with any fish no matter whether it is or a large predator. From the fisherman you only need to adjust the device under a certain breed and wait for the catch. Keep track of the power of the tension of the self-breed. Too strong will not let the opportunity to remove it from the stopper or the hook just ruins her mouth and she will leave. Weak tension H will have a proper effect on fish.
The principle of operation of the feeder for the feeder is very simple:
- the fishing rod is thrown into the desired distance in a certain place;
- balancer is installed in relation to the rack perpendicular and captured by the church;
- the fishing rod is inserted into the clamps on the balancar, the loose fishing line is wounded back;
- the fishing line starts for the mechanism tractor;
- during the Kleva, the fishing line pulls behind the lever, freeing the balance. The latter as a result of the spring tension force is upset up, producing a litter.
There is nothing complicated in the use of a self-spinner, and even a fisherman-novice can easily understand its action.
Making a self-breeder for feeder with your own hands
You can find many factory devices on sale. There are also various schemes of auto shifts for the manufacture of a panel for feeder with their own hands. They are simple and understandable, so make them independently difficult.
For simple and cheap design, the following materials and tools will be needed:
- stationery 2 pcs;
- clip 1 pc;
- pliers.
Stages of manufacturing a self-breed for feeder from a clip.
- The gums are burned to each other, connecting together.
- One end of the gum is mounted behind the feet of the coil.
- Metal clip straightens in a flat wire.
- Hooks are formed around the edges of the obtained wire.
- After throwing the bait, the device is fixed in one end to the first ring tackle.
- With the help of a fishing line, the self-spinner shall, the free end with the crochet is fixed.
- After setting, it is necessary to check the device's performance once, then weigh it back to the working position.
A more advanced type of automatic panel is similar to the Mousetrap Principle. It will take:
- bulgarian and drill with nozzles;
- metal rods with a diameter of 3 mm and 1.2 mm;
- dulely corner 25 * 25 mm;
- spring from the door;
- bolts and nuts.
Stages of manufacturing homemade panel.
- A rack is made from a duralumin or aluminum corner for fixing the device on the shore. Length is about 7-10 cm.
- Balancer with two brackets is made from the steel rod 3 mm, the rear of which is made in the form of the letter "D", the front in the form of "C". Both brackets should be perpendicular to the balance axis and one opposite each other.
- In the middle of the Balancir, there is a loop for fastening it on the rack. When flexing the front bracket, the loop is made for fastening the juro of the mechanism.
- The trigger with a loop, ring and hook is made of 1.2 mm steel rod. From it, the movable part of the mechanism is made. It consists of two connected straight cuts. The first connects with the front bracket together with the curcken, the second is a bit bend and skipped into the ring in the middle of the juro.
- The moving elements are fixed by 6-7 cm below from the top of the rack when it is in the working position. A small wire hook is installed on the back.
- With the help of a 6 mm bolt and the same nut to the head of the front bracket is attached to the trigger.
- In the rack, at a distance of about 25-30 cm from the vertex, up to 5 holes are drilled.
- Balancer is fastened at the stand of the loop using a 8 mm bolt and the appropriate nut.
- The spring is fixed by the hook of the handle for the holes on the rack and behind the rear bracket.
After assembling the device, the installation process of the device comes.
- Balancer is bent, forming a straight angle between its base and the top side of the rack.
- The connection of the moving sections of the trigger mechanism is attached to the hook on the back of the rack.
- The free end of one movable part is skipped into the trigger ring in the middle.
- The fishing rod is fixed in the balancing clamps, the excess fishing line is pulled out.
- The fishing line is tuned back and engages the jurka hook.
- Tightening, the fishing line raises the jurka hook, the end of a single movable part pops up from the hole of the jurka, freeing the rocker with the spring. The last jerk climbs up, performing a litter.
Having done everything right, you will get an excellent device for fishing. You can not be afraid with a self-breeder for the feeder that the work of fishing will remain without remuneration.
Of course, the sportiness of any gear with a fleering agent causes a grin, fishermen-athletes are generally ready for such fishing rods to equate poaching gear. Why do you need a fishing rod with a fleering agent?
First of all, it is needed on a large space: reservoir, lake, long plot of river. Preparation of auto shifts in different, separated from each other at a respectful distance, places of the reservoir, it is easy to determine the dope of fishing. And if these points are renovated, and the rods besides the slapper are equipped with sound signals, then the choice of fishing space will be determined even faster.
And there is an excitement at the time of making this gear. After all, it is interesting how to make a fishing rod, which herself catches fish! Try to make a car shift with your own hands - you will not regret the time spent on its manufacture and configuration.
Basis Fishing
For this model, rods with a fleering ager will take a piece of boards, chipboard, plywood and the like material. I was caught under the arm of the segment from the particle of 80x220 millimeters. In general, more than 100x300 do nothing - cumbersome, less - you will not argue elements.
Lever brag
In three centimeters from one of the edges of the board, we screw two brackets to install a lever of a slapper and secure them with small self-draws. The bracket for fastening can be made from sheet metal of various thicknesses, I used the details of the children's designer.
Spring production
We take two metal wires: thick for lever, thin for spring. Fat wire - element of the design of suspended ceilings, thin - from the old "string" type cornice. Holding one end thin wire pliers, wind the coil to the twist spring for the future lever. We do from ten to fifteen turns, so that the spring fit inside the bracket.
Mounting lever with spring
Bend lever and introduce a bracket. Then we wear a spring on the lever and push the lever into the bracket to the end. The long end of the springs wire bend from the bottom on the lever. Spring should pull the lever on itself. For fixing the lever, I pressed it with pliers.
Shock part
At the end of the lever, bend the shock part, as the next photo. Supleny cut off.
Fixator
So, the shock part of the mechanism is ready. We are taken for making a fixing part. We take another thick wire and bending something like this similar to the next shot.
Holes for fastening
In two centimeters from the other end of the base, we drill three pairs of holes for fastening the retainer.
Fastening the lock
Attach the lock to the base with the help of plastic screeds.
Lever with retainer
Check how the retainer will hold the lever of the slapper. If necessary, customize the design elements.
Elastic on the lock
We put on the fixator the stationery washing rubber, after having done a hole in it.
Refinement of gum clip
For greater reliability of fastening and visualization on snow Ice. We strengthen the rubber band on the lock with colored tapes. Slash in an elastic hole for skipping fishing line (its role in the picture is played by a red thread).
Hook tensioner
At a distance of about one centimeter from the lower bend of the lever, I mount the tensioner of the fishing line, the hook of the chandelier plays his role in the design.
